![where to get c 41 film developed where to get c 41 film developed](https://venturebeat.com/wp-content/uploads/2018/06/DOOM-VFR_20180607124532.jpg)
“Programming” of the device is super easy, some guy did a video so no point for me to repeat this. If in any doubt play it safe and get an electrician to do the wiring properly for you, we are talking mains power here, it can be dangerous. I have seen versions with separate 24v wires to power the device itself – these are no good. You need the 220v (or whatever the mains voltage is where you live) version that powers itself from the mains.
![where to get c 41 film developed where to get c 41 film developed](https://s3-us-east-2.amazonaws.com/fgwebsitemedia/wp-content/uploads/2017/08/02210631/DSC_0289.jpg)
The thermostat has just 4 wires + one wire that is the temperature probe. Wiring instructions are usually attached, if not just search the internet, these devices are extremely popular and have loads of uses. Thermostat measures the water temperature with a small probe and switches the heater on and off as required to keep the temperature at set level. You will need cheap thermostat from ebay – just look for “xh-w3001” on Ebay. Or if it is really warm where you develop. If you have a strong heater I am sure you can do without any kind of insulation at all. I also have another setup where I use a single storage container wrapped up in bubblewrap held in place by duct tape – works perfectly as well. It turned out to be working perfectly well though so I never bothered with the foam. Originally my idea was to use mounting foam as an insulator and bubblewrap was just a makeshift solution. I have one larger an one smaller container, but I suspect that if you have two containers of the same size the air gap between their walls can be sufficient as insulation. Another words the water in the container cools down at a slower rate.Īlso – my heater (only 80 Watts) is slightly too weak for the container size – insulation helps the heater to keep the temperature at the correct level. Bubblewrap serves as thermal insulation and thus decreases temperature fluctuation. I filled the space between them with bubblewrap.
![where to get c 41 film developed where to get c 41 film developed](https://petapixel.com/assets/uploads/2013/05/2013-05-12-20-56-58-copy-320x320.jpg)
I use two transparent plastic storage containers (bought off a pound store type of shop) that fit into one another. Heater, water agitation pump (for even heat distribution) and thermostat’s temperature probe Everything you need can be bought off Ebay and your local household goods stores. My DIY setup is really simple and very cheap. If you ever have a problematic roll and need to figure out what went wrong – then you have one thing less to take into account.Įven if you are a sworn lomographer you can still benefit from a good and carefree temperature control as it will make your developing techniques repeatable.
WHERE TO GET C 41 FILM DEVELOPED FREE
In E6 there is more to mess up as you can not only get too dark/too light slides but also color shifts – and there is no fixing in post if you want to use your slides with a projector.Įliminating the need to watch the temperature will free you up to do other elements of the process more accurately and will give you an overall more enjoyable experience. Generally in C41 process wrong temperature can give you under/overdeveloped (equalling to under/overexposed) film. There is a lot to do and you do not want to ruin your photos by making some silly mistake – just because you had too much to do at the same time.īoth C41 and E6 processes are temperature and time sensitive so keeping the temperature right is crucial from the quality standpoint. You will be busy watching the times, pouring different baths in and out, agitating. If you want to go this route I suggest you ask someone to keep an eye on water temperature for you, at least when you develop for the first time. You just fill your sink with warm water, control the temperature using a thermometer and add hot water when the temperature drops. There is no doubt that you can successfully develop C-41 film or even E-6 simply using your kitchen sink. I am not sure if they are still available brand new (like it or not analog photography is a dying art), but the used ones I saw for sale tend to be rather expensive. There are commercial devices for so called “rotary development” that go even one step further and also automate agitation process. Please watch the video below and read the post as together they contain the most complete information. It will make your home developing much more consistent and hassle free.
WHERE TO GET C 41 FILM DEVELOPED HOW TO
Here you will see how to build a simple DIY temperature controlled film development container. The temperature control is done by immersing your development tank (often called Paterson tank) in water of correct temperature. You pour your chemicals in and out while trying to keep the temperature at correct level. When developing films in C41 or E6 process at home you normally use a special lightproof tank with a spool containing your film inside. Cheap DIY temperature control setup for home film developing in C-41 and E6 processes